Hybrid solar inverter | 15KW | 48VDC |380Vac/400Vac/415Vac | Feed power into the grid
Prostar PSH-15KP mppt 48v dc into ac 3 phase 15kw hybrid inverter for home is self-consumption and feed power into the grid.
PSH-15KP 48v 3 phase 15kw hybrid inverter can run without battery backup. It is suitable for remote areas where the cost of the utility bill is too high or emergency usage when utility is not stable. It can operate as an off-grid inverter to provide continuous power even without the grid.
1. PV connectors 10. Operation buttons
2. AC Grid connectors 11. Dry contact
3. Battery connectors 12. Battery thermal sensor
4. AC output connectors 13. EPO
5. RS-232 communication port 14. AC circuit breaker
6. USB communication port 15. DC Switch
7. Intelligent slot 16. Relay control port
8. Grounding 17. Parallel communication port
9. LCD display panel 18. Current sharing port
This hybrid PV inverter can provide power to connected loads by utilizing PV power, utility power and battery power.
The runtime (i.e., amount of time that the inverter will power connected electronics) depends on the amount of battery power available and the load that it is supporting. In general, as you increase the load (e.g., plug in more equipment) your runtime will decrease. However, you can attach more batteries to extend the runtime. There is no limit to the number of batteries that can be connected.
Yes, no problem. If cables need to be run, it is best to keep the unit as close as possible to the batteries. Use extension cords on the output side (Vac output) rather than extending the VDC cables. Tip: Contractors often need to mount the inverter in the back of their trucks. In a case like this it would be best to mount a secondary battery near the inverter and wire it to the primary truck battery. Vac extension cords should not exceed 200 feet or you will have signal loss.
Most smaller appliances can be used with an inverter, such as a coffeemaker, smaller microwave, etc. To see if your appliance is safe for use with an inverter, verify with the appliance manufacturer.
Model | PSH-15KP |
PHASE | 3-phase in/3-phase out |
Max. PV INPUT POWER | 22500W |
Rated Output Power | 15000W |
Maximum Charging Power | 15000W |
Dimension, D x W x H (mm) | 219 x 600 x 820 |
Net weight (kgs) | 62 |
GRID-TIE OPERATION | |
PV INPUT (DC) | |
Nominal DC Voltage/Max. DC Voltage | 720VDC/900VDC |
Start-up Voltage/Initial Feeding Voltage | 320VDC/350VDC |
MPP Voltage Range | 400VDC~800VDC |
Number of MPP Trackers/Max. Input Current | 2/A: 37.65A; B: 18.6A |
GRID OUTPUT (AC) | |
Nominal Output Voltage | 230VAC (P-N) / 400VAC (P-P) |
Output Voltage Range | 184VAC – 265VAC* per phase |
Nominal Output Current | 21.7A per phase |
Power Factor | >0.99 |
EFFICIENCY | |
Maximum Conversion Efficiency (DC/AC) | 96% |
European Efficiency@Vnominal | 95% |
OFF-GRID OPERATION | |
AC INPUT | |
AC start-up Voltage / Auto Restart Voltage | 120VAC – 140VAC per phase/180 VAC per phase |
Acceptable Input Voltage Range | 170VAC – 280VAC per phase |
Max. AC Input Current | 40A |
PV INPUT (DC) | |
Max. DC Voltage | 900VDC |
MPP Voltage Range | 350VDC~850VDC |
Number of MPP Trackers/Max. Input Current | 2/A: 37.65A; B: 18.6A |
BATTERY Mode Output (AC) | |
Nominal Output Voltage | 230VAC (P-N) / 400 VAC (P-P) |
Output Waveform | Pure Sine Wave |
Efficiency (DC to AC) | 91% |
HYBRID OPERATION | |
PV INPUT (DC) | |
Nominal DC Voltage/Max. DC Voltage | 720VDC / 900VDC |
Start-up Voltage/Initial Feeding Voltage | 320VDC / 350VDC |
MPP Voltage Range | 350VDC~850VDC |
Number of MPP Trackers/Max. Input Current | 2/A: 37.65A; B: 18.6A |
GRID OUTOUT (AC) | |
Nominal Output Voltage | 230VAC (P-N) / 400 VAC (P-P) |
Output Voltage Range | 184VAC – 264.5 VAC* per phase |
Nominal Output Current | 14.5A per phase |
AC INPUT | |
AC Start-up Voltage/Auto Restart Voltage | 120VAC -140VAC per phase/ 180 VAC per phase |
Acceptable Input Voltage Range | 170VAC – 280VAC per phase |
Max. AC Input Current | 40A |
BATTERY MODE OUTPUT (AC) | |
Nominal Output Voltage | 230VAC (P-N) / 400 VAC(P-P) |
Efficiency (DC to AC) | 91% |
BATTERY& CHARGER | |
Nominal DC Voltage | 48VDC |
Max. Charging Current | Default 60A, 5A-300A (Adjustable) |
INTERFACE | |
Communication Port | RS-232/USB and CAN Interface |
Intelligent Slot | Optional SNMP, Modbus and AS-400 cards available |
ENVIRONMENT | |
Humidity | 0~90% RH (Non-condensing) |
Operating Temperature | -10 to 55 °C |
Altitude | 0-1000 m** |
*These figures may vary depending on different AC voltage and country requirements.
**Power derating 1% every 100m when altitude is over 1000m.
You must be logged in to post a comment.